Power Boat, Yacht, RIB, Race and Fleet GPS Global Tracking | Track Specification Sheet

Track800D - For Power Boat, Yacht, RIB, Race and fleet GPS Global Tracking-

INTERNAL COMPONENTS

Terminal Identification
GPS Receiver
Micro Controller
D+ Satellite Transceiver
Clock
Timer
Data Logger
Thermometer

POWER SUPPLY

Permanent 12v - 24v
Battery Pack
Solar Power

CONNECTIONS

10m Cable
Connectors

COMMUNICATION PORTS

Input/Output
RS232

PHYSICAL PROPERTIES

Size: 160mm (diameter) x 51mm (height) 520g (weight)
Enclosure: Weather Proof -40/+70
External LED Displays

DISPATCH

Packaging
Freight
Installation Instructions
Location & Fixing Kits
Activation Procedure
Certification

	COMPONENTS	SPECIFICATIONS	FEATURES	BENEFITS
INTERNAL COMPONENTS	Terminal Identification	Unique DCC number	The unique terminal identification and an individual password link the unit to a Solution Provider account and makes possible for the unit to be located and identified. It is impossible to use the unit with a different account or Solution Provider.	Personal, secure data transmission
	GPS Receiver	U-Blox receiver, 16 channels, 2.5m accuracy	Continuous and global GPS coverage; coordinates are calculated every 2-10 seconds with an accuracy of 2.5m. Units can be located with extreme accuracy, at any time, anywhere in the world.	Accurate asset location
	Micro Controller		The script is uploaded into the MC and the MC makes sure that the parameters within the script are performed in the correct sequence. The scripts have different content for different purposes: from regular tracking (data such as coordinates, speed, course, etc) and motion detection to speed and geofence alert ( when the asset enters a restricted zone or leaves a safe zone)	Customised scripts serve for different applications.
	D+ Transceiver	Global coverage Short Burst Messages	Payload (size limit): - From terminal: 64 bits - To terminal: 200 bits (133 characters) The messages transmitted can be: - Standard reports: predefined (coordinates, speed, course, voltage, temperature) - Custom reports: re-configurable, can vary depending on the application (oil monitoring, etc.). - Alerts: Triple burst (sent 3 times to ensure communication),Alerts sent to the user within 2 minutes. They can be transmitted to third parties such as the Coast Guard and Police.	Reliable, dependable, real-time communication, low failure rate. Customised report to suit different needs. Effective, reliable, quick communication in emergency situations
	Clock		Reports can be set to report at requested time	Accurate, real time reports
	Timer		Reports are sent at regular intervals of time depending on the script (from 1 to 96 reports per day). The timer is also used on the Idle Mode (see below) to indicate the unit when to go active again.	Reports received with very accurate timing.
	Data Logger	Up to 5,000 reports	Data can be stored within the unit and is available to the user.	Accessible data at any time
	Thermometer		Used in applications where temperature monitoring is required.	Temperature monitoring applications.
POWER SUPPLY	Permanent	Continuous power supply between 9VCD and 32VCD	Ideal DC source is 12V. Low power consumption 0.8W when receiving data and 10.2W when transmitting data) makes the solution very cost-effective.	Cost-effective solution
	Battery	Sleep or Shut down modes	The unit will continue reporting if the power supply is cut. Also used in: - Idle Mode: the unit switches itself on to report at certain times of the day and then switches itself off again; only the clock keeps operating during idle periods. The power consumption on this mode is 0.25W - Sleep Mode: the unit remains asleep, using the minimum amount of energy, until it receives a wake up command, it reports then and goes back to sleep after a few minutes. The power consumption on this mode is 0.05W	Energy-efficient modes
	Solar	Additional solar battery	A solar power charger can be installed in the unit to make it even more economical or as a backup source of energy.	Eco-friendly and economical
CONNECTIONS	Cable	10m cable
	Connectors	- 2 core (power and earth) or - 8 core conxall connector	The 2 core connector is only used for the tracking application. With the 8 core connector, additional applications can be connected (via input/output ports) to the unit.	Customised solutions to satisfy the customer’s needs.
COMMUNICATION PORTS	Input/Output	4 input/output ports	Devices such as alert buttons, sirens, lights and sensors Can be connected to the unit via these ports.	Different applications available
	RS232	1 input, 1 output ports	The unit is plugged into a DMT 50 which allows text messages to be transmitted and received.	Quick, short text messaging communication for remote location
PHYSICAL PROPERTIES	Size	160mm (diameter) x 51 mm (height). 520g (weight)	Very compact and light, it can be installed almost anywhere on the asset in a inconspicuous and unobtrusive way	Compact and discreet
	Enclosure	Weather proof	The unit can be used in adverse weather conditions and extreme climates and environments (it can operate between -40 and +70 degrees)	Long-lasting
	External Displays	STAT, TX and ERR LED	The LED displays flash in different sequences depending on the operating status.	Noticeable and easy to understand unit display
DISPATCH	Packaging	1 box with cable
	Freight	Carrier
	Instructions	On line
	Installation	Done by the user
	Location & Fixing Kits	Side or bottom mount connector
	Activation Procedure	Done by MSide or bottom mount connector	The units have to be linked to and activated by the solution provider to send and receive reports
	Certification